Abrasive Bits

Promed Sapphire Callus Grinder, Cone (198502) – for calluses and firm areas The Promed callus grinder in a cone shape with a natural sapphire coating removes calluses and hard skin on the feet. The cone shape reaches edges, corners and hard-to-reach areas well – ideal for targeted callus treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Shape: cone – for edges, corners and hard-to-reach areas. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: optimal 10,000, max. 15,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on corners: apply the cone shape precisely to edges and hard-to-reach areas. Hard skin: remove over a wide area in thin layers with little pressure. Tip: never remove too aggressively; work with little pressure and on a regular basis. Technical data Article number198502 Typecallus grinder, cone (sapphire) Materialsapphire (natural corundum) Application areaskin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedoptimal 10,000, max. 15,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with little pressure. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the cone shape good for? The cone shape reaches edges, corners and hard-to-reach callus areas precisely. Can I autoclave the grinder? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the cone-shaped Promed Sapphire Callus Grinder you treat calluses on edges and corners with precision.

Promed Sapphire Callus Grinder, Conical (198501) – for calluses on edges and corners The Promed callus grinder in a conical shape with a natural sapphire coating removes calluses and hard skin on the feet. The conical, tapering shape reaches edges, corners and narrower areas well – ideal for targeted treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Shape: conical – for edges, corners and narrower areas. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: optimal 10,000, max. 15,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on edges: apply the conical shape precisely to corners and narrower areas. Hard skin: remove over a wide area in thin layers with little pressure. Tip: never remove too aggressively; work with little pressure and on a regular basis. Technical data Article number198501 Typecallus grinder, conical (sapphire) Materialsapphire (natural corundum) Application areaskin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedoptimal 10,000, max. 15,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with little pressure. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the conical shape good for? The conical, tapering shape reaches edges, corners and narrower callus areas precisely. Can I autoclave the grinder? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the conical Promed Sapphire Callus Grinder you treat calluses on edges and corners with precision.

Promed Diamond Grinding Cone (198020) – for nail edges and cuticles The Promed Diamond Grinding Cone is a diamond-coated grinding bit for precise, gentle work on the natural nail. The cone shape reaches nail edges, corners and hard-to-access areas well and is ideal for shortening, shaping and working on the cuticle. Diamond works finely and in a controlled manner. Fits all Promed nail drills with a 2.35 mm collet. Features at a glance Material: diamond (diamond-coated) – precise and durable. Shape: cone – ideal for nail edges, corners and pinpoint work. Application: natural nail and skin/cuticle. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Nail edges: shape firm or thickened edges precisely with the cone tip. Cuticle: work on the cuticle gently and in a controlled manner. Tip: work at low to medium speed with little pressure; reduce the speed if heat builds up. Technical data Article number198020 Typegrinding cone, diamond Materialdiamond (diamond-coated) Shapecone Area of applicationnatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with little pressure; never stay too long on one spot on the nail. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the diamond grinding cone suitable for? For precise work on the natural nail – shaping nail edges and working gently on the cuticle. Diamond works finely and in a controlled manner. Can I autoclave the bit? Yes. This diamond grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. Which devices does it fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). With the Promed Diamond Grinding Cone you work on nail edges and cuticles precisely and gently.

Promed Diamond Bit, Teardrop (198542) – for the nail fold and cuticle The Promed Diamond Bit in a teardrop shape is a diamond-coated bit for precise, gentle work on the natural nail. The rounded teardrop shape reaches into the nail fold, edges and curves well and is suitable for shaping and gently working on the cuticle. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape: Teardrop – rounded, ideal for the nail fold, curves and edges. Application: Natural nail and skin/cuticle. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Nail fold: apply the rounded teardrop shape precisely in the nail fold and on curves. Cuticle: work on the cuticle gently and in a controlled way. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198542 TypeTeardrop bit, diamond MaterialDiamond (diamond-coated) ShapeTeardrop Application areaNatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the teardrop shape good for? The rounded teardrop shape reaches precisely into the nail fold, curves and edges – ideal for gentle detail work. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the Promed Diamond Teardrop Bit, you work on the nail fold and cuticle precisely and gently.

Promed Diamond Bit, Teardrop, small (198543) – for the fine nail fold and cuticle The small Promed Diamond Bit in a teardrop shape is a diamond-coated bit in a compact size for particularly fine, precise work on the natural nail. The small, rounded teardrop shape reaches into narrow nail folds, tight edges and curves well and is suitable for gently working on the cuticle. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape/size: Teardrop, small – for narrow nail folds and fine detail work. Application: Natural nail and skin/cuticle. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Narrow nail fold: apply the small, rounded teardrop shape precisely in narrow nail folds and on tight curves. Cuticle: work on the cuticle gently and in a controlled way. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198543 TypeTeardrop bit small, diamond MaterialDiamond (diamond-coated) Shape/sizeTeardrop, small Application areaNatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small teardrop shape good for? The small, rounded teardrop shape reaches precisely into narrow nail folds and onto tight curves – ideal for fine detail work. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the small Promed Diamond Teardrop Bit, you work in the narrow nail fold and on the cuticle with particular fineness.

Promed Diamond HHS Aero, large (198585) – callus grinder for the feet The Promed Diamond HHS Aero in the large version is a diamond-coated callus grinder for the targeted removal of calluses and hard skin on the feet. The large working surface is ideal for quick, area-wide removal of larger callused patches. Diamond works precisely and in a controlled manner. Fits all Promed rotary tools with a 2.35 mm collet. Key features at a glance Material: diamond (diamond-coated) – precise and durable. Shape/size: HHS Aero, large – large working surface for area-wide callus removal. Application: skin/calluses on the feet. Shaft: dental size Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Pronounced calluses: remove larger callused areas over a wide surface and in thin layers. Hard skin: work evenly with the large working surface. Tip: never remove calluses radically; work with little pressure and regularly. Reduce the speed if heat develops. Technical data Article number198585 TypeHHS Aero large, diamond (callus grinder) Materialdiamond (diamond-coated) Shape/sizeHHS Aero, large Application areaskin/calluses ShaftØ 2.332–2.350 mm (dental size) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed rotary tools with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses radically; work with little pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the large version good for? The large working surface is ideal for quick, area-wide removal of larger callused patches on the feet. Can I autoclave the bit? Yes. This diamond callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the large Promed Diamond HHS Aero you remove pronounced calluses on the feet quickly and evenly.

Promed Diamond HHS Aero, small (198586) – callus grinder for edges and corners The Promed Diamond HHS Aero in the small version is a diamond-coated callus grinder for the targeted removal of calluses and hard skin on the feet. The small working surface reaches edges, corners and narrower spots well – ideal for targeted work. Diamond works precisely and in a controlled manner. Fits all Promed rotary tools with a 2.35 mm collet. Key features at a glance Material: diamond (diamond-coated) – precise and durable. Shape/size: HHS Aero, small – for edges, corners and narrower callused spots. Application: skin/calluses on the feet. Shaft: dental size Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on edges: apply the small working surface precisely to corners and narrower spots. Hard skin: remove pinpoint and in thin layers with little pressure. Tip: never remove calluses radically; work with little pressure and regularly. Reduce the speed if heat develops. Technical data Article number198586 TypeHHS Aero small, diamond (callus grinder) Materialdiamond (diamond-coated) Shape/sizeHHS Aero, small Application areaskin/calluses ShaftØ 2.332–2.350 mm (dental size) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed rotary tools with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses radically; work with little pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small version good for? The small working surface reaches edges, corners and narrower callused spots on the feet in a targeted way. Can I autoclave the bit? Yes. This diamond callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the small Promed Diamond HHS Aero you work on calluses at edges and corners in a targeted way.

Promed Sapphire Callus Grinder Fine (190066) – for smoothing fine finishing The Promed callus grinder in a fine grit with a natural sapphire coating smooths the skin after callus removal and ensures a well-cared-for, soft result. The fine grit is ideal for the final fine finishing. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: fine – for smoothing fine finishing. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Fine finishing: smooth and refine the skin after coarser removal. Well-cared-for finish: for soft, even skin on the feet. Tip: work with light pressure and even movement; pause briefly if it gets warm. Technical data Article number190066 TypeCallus grinder, fine (sapphire) MaterialSapphire (natural corundum) Gritfine Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use fine, when coarse? The fine grit is for the final fine finishing and smoothing of the skin; use a coarser grit for the intensive first removal. Can I autoclave the bit? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the fine Promed sapphire callus grinder, you can smooth the skin for a well-cared-for finish.

Promed Sapphire Callus Grinder Coarse (190063) – for pronounced calluses The Promed callus grinder in a coarse grit with a natural sapphire coating removes pronounced calluses and hard skin on the feet quickly and over a wide area. The coarse grit is ideal for the first, more intensive treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: coarse – for intensive callus removal. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: in an ultrasonic bath. What is it used for and how? Pronounced calluses: remove over a wide area in thin layers – for the first, coarser working step. Fine finishing afterwards: then smooth with a finer grit. Tip: never remove too much at once; work with light pressure and on a regular basis. Technical data Article number190063 TypeCallus grinder, coarse (sapphire) MaterialSapphire (natural corundum) Gritcoarse Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean after use in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use coarse, when fine? The coarse grit is for the intensive first removal of pronounced calluses; use a finer grit for the subsequent fine finishing. Which devices does it fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). With the coarse Promed sapphire callus grinder, you can remove pronounced calluses quickly and safely.

Promed Sapphire Callus Grinder Coarse (190067) – for pronounced calluses The Promed callus grinder in a coarse grit with a natural sapphire coating removes pronounced calluses and hard skin on the feet quickly and over a wide area. The coarse grit is ideal for the first, more intensive treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: coarse – for intensive callus removal. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: in an ultrasonic bath; not autoclavable. What is it used for and how? Pronounced calluses: remove over a wide area in thin layers – for the first, coarser working step. Fine finishing afterwards: then smooth with a finer grit. Tip: never remove too much at once; work with light pressure and on a regular basis. Technical data Article number190067 TypeCallus grinder, coarse (sapphire) MaterialSapphire (natural corundum) Gritcoarse Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationnot autoclavable; ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean after use in an ultrasonic bath (e.g. Promed UC-50 / UC-60); do not autoclave. Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use coarse, when fine? The coarse grit is for the intensive first removal of pronounced calluses; use a finer grit for the subsequent fine finishing. Can I autoclave the bit? No. This callus grinder is not autoclavable – clean it in an ultrasonic bath. With the coarse Promed sapphire callus grinder, you can remove pronounced calluses quickly and safely.

Promed Sapphire Callus Grinder Medium (190064) – for quick callus treatment The Promed callus grinder in a medium grit with a natural sapphire coating removes calluses and hard skin on the feet evenly. The medium grit is the all-rounder between intensive removal and fine finishing. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: medium – the all-rounder for callus treatment. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses: remove evenly and in thin layers – ideal for regular care. After coarse removal: as the intermediate step before the final fine finishing. Tip: never remove too much at once; work with light pressure and on a regular basis. Technical data Article number190064 TypeCallus grinder, medium (sapphire) MaterialSapphire (natural corundum) Gritmedium Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use medium, when coarse or fine? The medium grit is the all-rounder: for regular callus care or as an intermediate step between coarse removal and a fine finish. Can I autoclave the bit? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the medium Promed sapphire callus grinder, you can care for calluses evenly and regularly.

Promed Polishing Cone Felt (190041) – for a silky high gloss on the nail surface The Promed Polishing Cone made of felt is the finishing attachment for a silky high gloss. It smooths the nail surface and brings it – often together with polishing paste – to a natural shine. The cone shape reaches the surface, corners and edges well. The polishing cone does not remove any material, it polishes. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: felt. Shape: cone – for the surface, corners and edges. Function: high-gloss polishing of the nail surface – not for material removal. Application: natural nail and artificial nail. Shank: dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 10,000 rpm. Cleaning: in an ultrasonic bath; not autoclavable. What is it used for and how?The felt polishing cone is the final step for a shiny natural nail: High-gloss polish: guide it over the previously smoothed nail surface at low speed and with light pressure – optionally with a little polishing paste for a more intense shine. Tip: use it after the silicone polishers (coarse → medium → fine) to round off the finish. Note: if heat builds up, reduce the speed and lift the attachment off briefly. Technical data Article number190041 TypePolishing cone, felt MaterialFelt FunctionHigh-gloss polishing (no material removal) Application areaNatural nail, artificial nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 10,000 rpm Sterilizationnot autoclavable; ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe polishing cone fits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60); do not autoclave (heat-sensitive). Work at low speed and with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Does the polishing cone remove material? No. The felt polishing cone smooths and polishes the nail surface to a high gloss – it is not intended for material removal. What speed should I work at? At low speed (up to 10,000 rpm) and with light pressure. If heat builds up, reduce the speed. Can I autoclave the polishing cone? No. Polishers are heat-sensitive and not autoclavable – clean them in an ultrasonic bath. With the Promed Polishing Cone Felt you bring the nail surface to a silky high gloss.

Promed Sanding Band ZEBRA coarse, 100 pieces (198592) – single-use slip-on sleeves for natural nails and calluses The Promed Sanding Bands ZEBRA in the coarse grit are single-use slip-on sleeves for working on natural nails and calluses. The ZEBRA version is recognisable by its characteristic striped pattern; the coarse grit is suitable for the vigorous removal of pronounced calluses and thicker areas of the nail. The bands are slipped onto a Promed sanding mandrel and are changed after use for hygiene reasons. For all Promed rotary tools with a 2.35 mm collet. Key features at a glance Version: ZEBRA – characteristic striped pattern. Grit: coarse – vigorous removal of pronounced calluses and thicker areas of the nail. Type: single-use slip-on sleeve – changed for hygiene reasons. Pack size: 100 pieces. Application: natural nails and skin/calluses. Recommended speed: approx. 4,000–15,000 rpm. Cleaning: single-use / hygiene change; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e. g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Slipping on: push the sanding band onto the Promed sanding mandrel until it sits securely. Working: remove pronounced calluses or thicker areas of the nail with light pressure in thin layers – never radically. Changing: pull off the band after use and dispose of it; slip on a fresh one for the next treatment. Technical data Article number198592 TypeSanding band ZEBRA (single-use slip-on sleeve) Gritcoarse Pack size100 pieces Application areanatural nails, skin/calluses Recommended speedapprox. 4,000–15,000 rpm Sterilisationsingle-use / hygiene change; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are slipped onto a Promed sanding mandrel (e. g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed rotary tools with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: change after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What does ZEBRA mean? ZEBRA refers to the version of the sanding bands with a characteristic striped pattern. Function and application are the same as for the other sanding bands. What is the coarse grit intended for? For the vigorous removal of pronounced calluses and thicker areas of the nail. For finer reworking, then switch to ZEBRA medium (198591) or ZEBRA fine (198590). With the coarse Promed Sanding Bands ZEBRA you vigorously remove pronounced calluses – hygienically with a fresh sleeve for every treatment.

Promed Sanding Band ZEBRA fine, 100 pieces (198590) – single-use slip-on sleeves for natural nail and calluses The Promed Sanding Bands ZEBRA in fine grit are single-use slip-on sleeves for working on the natural nail and calluses. The ZEBRA version is recognisable by its characteristic striped pattern; the fine grit is suited for gentle smoothing and finer finishing. The bands are fitted onto a Promed sanding mandrel and replaced after use for hygiene reasons. For all Promed rotary tools with a 2.35 mm collet. Key features at a glance Version: ZEBRA – characteristic striped pattern. Grit: fine – gentle smoothing and fine finishing. Type: single-use slip-on sleeve – replace for hygiene reasons. Pack size: 100 pieces. Application: natural nail and skin/calluses. Recommended speed: approx. 4,000–15,000 rpm. Cleaning: single-use / hygiene replacement; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e.g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Fitting: slide the sanding band onto the Promed sanding mandrel until it sits securely. Working: finely work the natural nail or calluses with light pressure – never aggressively, but in thin layers. Replacing: pull off and dispose of the band after use; fit a fresh one for the next treatment. Technical data Article number198590 TypeSanding band ZEBRA (single-use slip-on sleeve) Gritfine Pack size100 pieces Application areanatural nail, skin/calluses Recommended speedapprox. 4,000–15,000 rpm Sterilisationsingle-use / hygiene replacement; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are fitted onto a Promed sanding mandrel (e.g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed rotary tools with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: replace after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses aggressively. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What does ZEBRA mean? ZEBRA refers to the version of the sanding bands with a characteristic striped pattern. Function and application correspond to the other sanding bands. Do I need a mandrel as well? Yes. The sanding bands are fitted onto a Promed sanding mandrel (available separately). They cannot be used without a mandrel. With the fine Promed Sanding Bands ZEBRA you smooth the natural nail and calluses hygienically with a fresh sleeve for every treatment.

Promed Sanding Band ZEBRA medium, 100 pieces (198591) – single-use slip-on sleeves for natural nail and calluses The Promed Sanding Bands ZEBRA in medium grit are single-use slip-on sleeves for working on the natural nail and calluses. The ZEBRA version is recognisable by its characteristic striped pattern; the medium grit is the versatile all-rounder for quick material removal. The bands are fitted onto a Promed sanding mandrel and replaced after use for hygiene reasons. For all Promed rotary tools with a 2.35 mm collet. Key features at a glance Version: ZEBRA – characteristic striped pattern. Grit: medium – versatile all-rounder for quick material removal. Type: single-use slip-on sleeve – replace for hygiene reasons. Pack size: 100 pieces. Application: natural nail and skin/calluses. Recommended speed: approx. 4,000–15,000 rpm. Cleaning: single-use / hygiene replacement; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e.g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Fitting: slide the sanding band onto the Promed sanding mandrel until it sits securely. Working: work the natural nail or calluses with light pressure – never aggressively, but in thin layers. Replacing: pull off and dispose of the band after use; fit a fresh one for the next treatment. Technical data Article number198591 TypeSanding band ZEBRA (single-use slip-on sleeve) Gritmedium Pack size100 pieces Application areanatural nail, skin/calluses Recommended speedapprox. 4,000–15,000 rpm Sterilisationsingle-use / hygiene replacement; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are fitted onto a Promed sanding mandrel (e.g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed rotary tools with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: replace after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses aggressively. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What does ZEBRA mean? ZEBRA refers to the version of the sanding bands with a characteristic striped pattern. Function and application correspond to the other sanding bands. Which grit should I choose? The medium grit is the all-rounder for quick material removal. For finer smoothing choose ZEBRA fine (198590), for coarser removal ZEBRA coarse (198592). With the medium Promed Sanding Bands ZEBRA you work the natural nail and calluses versatilely – hygienically with a fresh sleeve for every treatment.

Promed Sanding Band coarse, 100 pieces (198563) – single-use slip-on sleeves for natural nails and calluses The Promed Sanding Bands in a coarse grit are single-use slip-on sleeves for working on natural nails and calluses. The coarse grit is suitable for the vigorous removal of pronounced calluses and thicker areas of the nail. The bands are pushed onto a Promed sanding mandrel and changed after use for hygiene reasons. For all Promed nail drills with a 2.35 mm collet. Key features at a glance Grit: coarse – vigorous removal of pronounced calluses and thicker areas of the nail. Design: single-use slip-on sleeve – changed for hygiene reasons. Pack size: 100 pieces. Application: Natural nail and skin/calluses. Recommended speed: runs with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm). Cleaning: single-use / hygiene change; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e.g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Attaching: slide the sanding band onto the Promed sanding mandrel until it sits securely. Working: remove pronounced calluses or thicker areas of the nail with light pressure in thin layers – never aggressively. Changing: pull off the band after use and dispose of it; put on a fresh one for the next treatment. Technical data Article number198563 TypeSanding band (single-use slip-on sleeve) Gritcoarse Pack size100 pieces Application areaNatural nail, skin/calluses Recommended speedruns with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm) Sterilisationsingle-use / hygiene change; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are pushed onto a Promed sanding mandrel (e.g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed nail drills with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: change them after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses aggressively. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the coarse grit intended for? For the vigorous removal of pronounced calluses and thicker areas of the nail. For finer finishing, switch to medium (198562) or fine (198561) afterwards. Do I need a mandrel for them? Yes. The sanding bands are pushed onto a Promed sanding mandrel (available separately). Without a mandrel they cannot be used. With the coarse Promed Sanding Bands, you vigorously remove pronounced calluses – hygienically with a fresh sleeve for every treatment.

Promed Sanding Band fine, 100 pieces (198561) – single-use slip-on sleeves for natural nails and calluses The Promed Sanding Bands in a fine grit are single-use slip-on sleeves for working on natural nails and calluses. The fine grit is suitable for gentle smoothing and finer finishing. The bands are pushed onto a Promed sanding mandrel and changed after use for hygiene reasons. For all Promed nail drills with a 2.35 mm collet. Key features at a glance Grit: fine – gentle smoothing and fine finishing. Design: single-use slip-on sleeve – changed for hygiene reasons. Pack size: 100 pieces. Application: Natural nail and skin/calluses. Recommended speed: runs with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm). Cleaning: single-use / hygiene change; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e.g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Attaching: slide the sanding band onto the Promed sanding mandrel until it sits securely. Working: finely work on the natural nail or calluses with light pressure – never aggressively, but in thin layers. Changing: pull off the band after use and dispose of it; put on a fresh one for the next treatment. Technical data Article number198561 TypeSanding band (single-use slip-on sleeve) Gritfine Pack size100 pieces Application areaNatural nail, skin/calluses Recommended speedruns with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm) Sterilisationsingle-use / hygiene change; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are pushed onto a Promed sanding mandrel (e.g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed nail drills with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: change them after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses aggressively. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Do I need a mandrel for them? Yes. The sanding bands are pushed onto a Promed sanding mandrel (available separately). Without a mandrel they cannot be used. Can I use the bands more than once? Sanding bands are single-use hygiene items and are changed after use. They are not autoclavable. The pack of 100 is enough for many applications. With the fine Promed Sanding Bands, you smooth natural nails and calluses hygienically with a fresh sleeve for every treatment.

Promed Sanding Band medium, 100 pieces (198562) – single-use slip-on sleeves for natural nails and calluses The Promed Sanding Bands in a medium grit are single-use slip-on sleeves for working on natural nails and calluses. The medium grit is the versatile all-rounder for quick removal and preparing finer steps. The bands are pushed onto a Promed sanding mandrel and changed after use for hygiene reasons. For all Promed nail drills with a 2.35 mm collet. Key features at a glance Grit: medium – versatile all-rounder for quick removal. Design: single-use slip-on sleeve – changed for hygiene reasons. Pack size: 100 pieces. Application: Natural nail and skin/calluses. Recommended speed: runs with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm). Cleaning: single-use / hygiene change; not autoclavable. Compatible accessories: Promed sanding mandrel as carrier (e.g. 198564, 198565/L, 198583, 198580, 198581). What are they used for and how? Attaching: slide the sanding band onto the Promed sanding mandrel until it sits securely. Working: work on the natural nail or calluses with light pressure – never aggressively, but in thin layers. Changing: pull off the band after use and dispose of it; put on a fresh one for the next treatment. Technical data Article number198562 TypeSanding band (single-use slip-on sleeve) Gritmedium Pack size100 pieces Application areaNatural nail, skin/calluses Recommended speedruns with the carrier mandrel (rubber up to 15,000 / metal up to 25,000 rpm) Sterilisationsingle-use / hygiene change; not autoclavable CompatibilityPromed sanding mandrel; all Promed devices with a 2.35 mm collet Compatible accessoriesThe sanding bands are pushed onto a Promed sanding mandrel (e.g. plastic 198564, plastic long 198565/L, metal autoclavable 198583 or rubber 198580 / 198581). The mandrel fits all Promed nail drills with a standard collet (2.35 mm). Care and safety instructions Sanding bands are single-use items: change them after use for hygiene reasons, do not autoclave. Work with light pressure; never remove calluses aggressively. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Do I need a mandrel for them? Yes. The sanding bands are pushed onto a Promed sanding mandrel (available separately). Without a mandrel they cannot be used. Which grit should I choose? The medium grit is the all-rounder for quick removal. For finer smoothing choose fine (198561), for coarser removal choose coarse (198563). With the medium Promed Sanding Bands, you work on natural nails and calluses versatilely – hygienically with a fresh sleeve for every treatment.

Promed Sapphire Grinding Cone (190021) – for calluses and firm nail edges The Promed Sapphire Grinding Cone is a durable grinding tool with a natural sapphire coating for the targeted removal of calluses, hard skin and firm nail edges. The cone shape reaches corners, edges and hard-to-reach areas well. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and long-lasting. Shape: Cone – ideal for edges, corners and precise work. Application: Skin/calluses and natural nails. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: in an ultrasonic bath; not autoclavable. What is it used for and how?The sapphire grinding cone is suitable for gently and regularly removing calluses and for working on firm nail edges on hands and feet: Calluses & hard skin: remove over a wide area at low to medium speed with light pressure – never radically, but regularly in thin layers. Nail edges: carefully shape firm or thickened edges. Tip: if heat develops, reduce the speed and briefly lift the bit off. Technical data Article number190021 TypeGrinding cone, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationnot autoclavable; ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60) after use; do not autoclave. Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Which devices does the grinding cone fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Can I autoclave the bit? No. This sapphire grinding cone is not autoclavable – clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are more suitable. With the Promed Sapphire Grinding Cone, you work on calluses and firm nail edges precisely and durably.

Promed Sapphire Grinding Cone (190028) – for calluses and firm nail edges The Promed Sapphire Grinding Cone is a durable grinding tool with a natural sapphire coating for the targeted removal of calluses, hard skin and firm nail edges. The cone shape reaches corners, edges and hard-to-reach areas well. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and long-lasting. Shape: Cone – ideal for edges, corners and precise work. Application: Skin/calluses and natural nails. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how?The sapphire grinding cone is suitable for gently and regularly removing calluses and for working on firm nail edges on hands and feet: Calluses & hard skin: remove over a wide area at low to medium speed with light pressure – never radically, but regularly in thin layers. Nail edges: carefully shape firm or thickened edges. Tip: if heat develops, reduce the speed and briefly lift the bit off. Technical data Article number190028 TypeGrinding cone, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Which devices does the grinding cone fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Can I autoclave the bit? Yes. This sapphire grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are more suitable. With the Promed Sapphire Grinding Cone, you work on calluses and firm nail edges precisely and durably.

Promed Sapphire Grinding Cone (190024) – for calluses and firm nail edges The Promed Sapphire Grinding Cone is a durable grinding tool with a natural sapphire coating for the targeted removal of calluses, hard skin and firm nail edges. The cone shape reaches corners, edges and hard-to-reach areas well. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and long-lasting. Shape: Cone – ideal for edges, corners and precise work. Application: Skin/calluses and natural nails. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how?The sapphire grinding cone is suitable for gently and regularly removing calluses and for working on firm nail edges on hands and feet: Calluses & hard skin: remove over a wide area at low to medium speed with light pressure – never radically, but regularly in thin layers. Nail edges: carefully shape firm or thickened edges. Tip: if heat develops, reduce the speed and briefly lift the bit off. Technical data Article number190024 TypeGrinding cone, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Which devices does the grinding cone fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Can I autoclave the bit? Yes. This sapphire grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are more suitable. With the Promed Sapphire Grinding Cone, you work on calluses and firm nail edges precisely and durably.

Promed Sapphire Grinding Cone (190026) – for calluses and firm nail edges The Promed Sapphire Grinding Cone is a durable grinding tool with a natural sapphire coating for the targeted removal of calluses, hard skin and firm nail edges. The cone shape reaches corners, edges and hard-to-reach areas well. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and long-lasting. Shape: Cone – ideal for edges, corners and precise work. Application: Skin/calluses and natural nails. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how?The sapphire grinding cone is suitable for gently and regularly removing calluses and for working on firm nail edges on hands and feet: Calluses & hard skin: remove over a wide area at low to medium speed with light pressure – never radically, but regularly in thin layers. Nail edges: carefully shape firm or thickened edges. Tip: if heat develops, reduce the speed and briefly lift the bit off. Technical data Article number190026 TypeGrinding cone, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) Which devices does the grinding cone fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Can I autoclave the bit? Yes. This sapphire grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are more suitable. With the Promed Sapphire Grinding Cone, you work on calluses and firm nail edges precisely and durably.

Promed Sapphire Grinding Cone, small (190031) – for fine and small areas The Promed Sapphire Grinding Cone in the small version is a durable grinding tool with a natural sapphire coating. Its small, slim head reaches fine and hard-to-access areas with precision – ideal for the targeted treatment of firm nail edges and smaller callus areas. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and durable. Shape: small cone – for fine, small and hard-to-reach areas. Application: skin/calluses and natural nail. Shank: dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how?The small sapphire grinding cone is suited to fine, targeted treatment on hands and feet: Nail edges & corners: shape firm or thickened edges and tight corners with precision. Small callus areas: remove limited hard skin over the surface with light pressure. Tip: the small head allows precise work; if heat builds up, reduce the speed and lift off briefly. Technical data Article number190031 TypeGrinding cone small, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilizationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small version good for? The small head is suited to fine, small and hard-to-reach areas – such as tight nail edges and limited callus areas. Can I autoclave the bit? Yes. This sapphire grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are better suited. With the small Promed Sapphire Grinding Cone you work on fine and hard-to-reach areas with particular precision.

Promed Sapphire Grinding Cone small (190027) – for fine and small areas The Promed Sapphire Grinding Cone in a small design is a durable grinding tool with a natural sapphire coating. Its small, slim head reaches fine and hard-to-reach areas precisely – ideal for the accurate treatment of firm nail edges and smaller callus areas. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Sapphire (natural corundum) – robust and long-lasting. Shape: Small cone – for fine, small and hard-to-reach areas. Application: Skin/calluses and natural nails. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how?The small sapphire grinding cone is suitable for fine, precise work on hands and feet: Nail edges & corners: precisely shape firm or thickened edges and tight corners. Small callus areas: remove limited hard skin over a wide area with light pressure. Tip: the small head allows precise work; if heat develops, reduce the speed and briefly lift off. Technical data Article number190027 TypeGrinding cone small, sapphire MaterialSapphire (natural corundum) Application areaSkin/calluses, natural nail ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe grinding cone fits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never remove calluses radically. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small version good for? The small head is suitable for fine, small and hard-to-reach areas – such as tight nail edges and limited callus areas. Can I autoclave the bit? Yes. This sapphire grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. For natural or artificial nails? Primarily for skin/calluses and the natural nail. For artificial nails, tungsten carbide or diamond bits are more suitable. With the small Promed Sapphire Grinding Cone, you work particularly precisely on fine and hard-to-reach areas.