Manicure and Pedicure
Promed Callus Set (198010) – bits for foot care and calluses The Promed Callus Set is put together specifically for foot care. It bundles several bits for removing calluses, hard skin and firm nail edges on the feet, both over larger areas and in a targeted way. All bits have a shaft Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Focus: foot care – calluses, hard skin and firm nail edges. Contents: several bits for large-area removal and targeted edge work. Target group: users with pronounced calluses as well as foot care. Shaft: dental standard Ø 2.332–2.350 mm, suitable for all Promed devices with a standard collet. Cleaning: in an ultrasonic bath. Important: this set is expressly NOT autoclavable. What is the set used for and how?The Callus Set is suitable for regular foot care: Calluses & hard skin: remove over larger areas and with light pressure – never radically, but regularly in thin layers. Nail edges: carefully shape firm or thickened edges on the toenails. Tip: if heat builds up, reduce the speed and briefly lift off the bit. Technical data Article number198010 TypeSanding bit set, Callus (foot care) Application areaFoot care – calluses, hard skin, firm nail edges ShaftØ 2.332–2.350 mm (dental standard) Sterilisationnot autoclavable; ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60); do not autoclave. Work with light pressure; never remove calluses radically. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shaft Ø 2.35 mm). Can I autoclave the Callus Set? No. This set is expressly not autoclavable – clean the bits in an ultrasonic bath. What is the set intended for? For foot care – the targeted, regular removal of calluses, hard skin and firm nail edges. With the Promed Callus Set, you work on calluses and firm nail edges on the feet in a targeted and regular way.
Promed Polisher Set (198007) – polishers for a high-gloss finish on nails The Promed Polisher Set combines several polishers (bits) for the final step: smoothing and bringing the nail surface to a high gloss. The soft to medium polishing bits refine natural and artificial nails without removing too much material. All bits have a shank Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Type: polisher set for a high gloss and smooth surfaces. Contents: several polishing bits in various shapes and degrees of hardness. Application: finish and shine on natural and artificial nails. Target group: nail salons and home users for the perfect finishing touch. Shank: dental size Ø 2.332–2.350 mm, compatible with all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits autoclavable depending on marking. What is the set used for and how?The Polisher Set is used at the end of the treatment: Smoothing: even out fine ridges and unevenness on the nail surface. High gloss: bring the surface to a natural shine without polish. Tip: work at low speed and with very little pressure to avoid heat. Technical data Article number198007 TypePolisher set (polishers) Area of applicationFinish and high gloss, natural and artificial nails ShankØ 2.332–2.350 mm (dental size) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean in an ultrasonic bath after use (e.g. Promed UC-50 / UC-60). Only autoclave individual bits that are marked accordingly – observe the marking of the respective bit. Work with very little pressure and avoid heat generation. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Are the polishers autoclavable? Depending on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Do I need additional polish for the shine? No. The polishers bring the nail surface to a natural high gloss – entirely without polish. With the Promed Polisher Set you give natural and artificial nails the perfect high-gloss finish.
Promed Set Basic (198005) – basic kit for manicure and pedicure The Promed Set Basic is the compact starter kit for nail and foot care. It brings together a well-chosen selection of bits for the most important steps in manicure and pedicure – ideal for getting started or as a foundation you can expand specifically later on. All bits have a shank Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Contents: balanced basic selection of bits for manicure and pedicure. Application: shortening, shaping and smoothing nails as well as light skin work. Target group: beginners and home users looking for a solid basic kit. Shank: dental size Ø 2.332–2.350 mm, compatible with all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits autoclavable depending on marking. What is the set used for and how?Set Basic covers the everyday care steps: Nails: shorten, shape and smooth the edges. Skin: carefully work light calluses and firm edges. Tip: work at low to medium speed and with little pressure – particularly easy to control for beginners. Technical data Article number198005 TypeGrinding bit set, Basic Area of applicationManicure and pedicure (basic kit) ShankØ 2.332–2.350 mm (dental size) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean in an ultrasonic bath after use (e.g. Promed UC-50 / UC-60). Only autoclave individual bits that are marked accordingly – observe the marking of the respective bit. Work with little pressure; in case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Are the bits autoclavable? Depending on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Is the set suitable for beginners? Yes. Set Basic is put together as a basic kit for beginners and home users in manicure and pedicure. With the Promed Set Basic you start manicure and pedicure with a solid basic kit.
Promed Set Master (198006) – comprehensive professional set for manicure and pedicure The Promed Set Master is the comprehensive professional selection for demanding nail and foot care. It combines a broad range of bits in various materials, shapes and grits – covering almost every step in manicure and pedicure. All bits have a shank Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Contents: broad range of bits in different materials, shapes and grits. Application: the complete spectrum from nail to skin work in manicure and pedicure. Target group: professionals, salons and ambitious users with high standards. Shank: dental size Ø 2.332–2.350 mm, compatible with all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits autoclavable depending on marking. What is the set used for and how?Set Master covers the full range of professional care: Nails: shorten, shape, smooth and work the surface. Skin: specifically work calluses, hardened skin and firm nail edges. Detail work: work corners, edges and hard-to-reach areas. Tip: adjust the speed and bit to each step; work with little pressure. Technical data Article number198006 TypeGrinding bit set, Master Area of applicationManicure and pedicure (professional set) ShankØ 2.332–2.350 mm (dental size) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean in an ultrasonic bath after use (e.g. Promed UC-50 / UC-60). Only autoclave individual bits that are marked accordingly – observe the marking of the respective bit. Work with little pressure; in case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). Are the bits autoclavable? Depending on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Who is the set suitable for? For professionals, salons and ambitious users looking for a comprehensive set for almost every step. With the Promed Set Master you have the right bit to hand for every step in manicure and pedicure.
Promed Natural Set (198009) – gentle bits for the natural nail The Promed Natural Set is designed for the gentle care of the natural nail. It contains several fine bits for gently shortening, shaping and smoothing – without putting unnecessary strain on the nail. Ideal for anyone who values natural, well-groomed nails. All bits have a shaft Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Focus: gentle, careful treatment of the natural nail. Contents: several fine bits for shortening, shaping and smoothing. Application: natural nail care as well as light work on the cuticle and edges. Target group: users focused on natural, well-groomed nails. Shaft: dental standard Ø 2.332–2.350 mm, suitable for all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits are autoclavable depending on their marking. What is the set used for and how?The Natural Set is suitable for regular, gentle nail care: Shortening & shaping: gently bring the natural nail to length and shape. Smoothing: finely work the edges and surface. Detail work: carefully care for the cuticle and edges. Tip: work at a low speed and with light pressure – especially gentle on the natural nail. Technical data Article number198009 TypeSanding bit set, Natural Application areaNatural nail care (gentle) ShaftØ 2.332–2.350 mm (dental standard) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Autoclave only bits marked accordingly – observe the marking of the respective bit. Work at a low speed and with light pressure; do not overstrain the natural nail. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shaft Ø 2.35 mm). Are the bits autoclavable? It depends on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Is the set suitable for artificial nails? The Natural Set is designed for the gentle care of the natural nail. For artificial nails, carbide or nitride sets are more suitable. With the Promed Natural Set, you care for the natural nail gently and keep it well-groomed in the long term.
Promed Personal Care Set (198014) – bits for nail and foot care at home The Promed Personal Care Set is the practical selection for nail and foot care in your own home. It bundles a clearly arranged choice of bits for the most important care steps on hands and feet – easy to use and ideal for home use. All bits have a shaft Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Focus: home use – nail and foot care for at home. Contents: a clearly arranged choice of bits for everyday care. Application: shortening and shaping nails as well as working on skin and light calluses. Target group: home users who want to care for their hands and feet themselves. Shaft: dental standard Ø 2.332–2.350 mm, suitable for all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits are autoclavable depending on their marking. What is the set used for and how?The Personal Care Set covers everyday care at home: Nails: shorten, shape and smooth on hands and feet. Skin: carefully work on light calluses and firm edges. Tip: work at a low to medium speed and with light pressure – easy to control. Technical data Article number198014 TypeSanding bit set, Personal Care Application areaHome use – nail and foot care ShaftØ 2.332–2.350 mm (dental standard) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Autoclave only bits marked accordingly – observe the marking of the respective bit. Work with light pressure; in case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shaft Ø 2.35 mm). Are the bits autoclavable? It depends on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Is the set suitable for beginners? Yes. The Personal Care Set is specially put together for easy nail and foot care at home. With the Promed Personal Care Set, you care for your hands and feet conveniently and easily at home.
Promed Cleaning Brush, brass (198910) – coarse cleaning for bits The Promed Cleaning Brush made of brass removes dust, grinding residue and coarse deposits from bits, cutters and grinding tools – ideal as a first step before the ultrasonic bath. The fine brass bristles also reach well into grooves and along grinding surfaces and loosen stubborn deposits. Key features at a glance Function: coarse cleaning of bits before the ultrasonic bath. Bristles: brass – strong for stubborn residue. Application: remove grinding residue and dust from grooves and grinding surfaces. Suitable for: bits and grinding tools with a standard shank of 2.35 mm. Cleaning: rinse after use and let dry. What is it used for and how?The brass brush is the first cleaning step so that the subsequent ultrasonic bath can work thoroughly: Pre-cleaning: guide the bit dry or damp over the bristles until the residue is loosened. Afterwards: clean the bits again in the ultrasonic bath (UC-50 / UC-60). Tip: work with light pressure on sensitive coatings. Technical data Article number198910 TypeCleaning brush BristlesBrass Applicationcoarse cleaning of bits / grinding tools Cleaningrinse, let dry Matching accessoriesFor the coarse cleaning of all Promed bits and grinding tools. For the subsequent fine cleaning, the ultrasonic cleaner UC-50 (330210) / UC-60 (330212/330213) is suitable. Alternatives with nylon bristles: 198920 (white) and 198930 (with twist mechanism). Care and safety instructions Rinse after use and let dry; store in a dry place. Work with light pressure on coated or sensitive bits. Coarse cleaning does not replace disinfection/sterilisation – follow your hygiene plan. Frequently asked questions (FAQ) What is the brass brush intended for? For the coarse cleaning of bits – removing dust and grinding residue before the bits go into the ultrasonic bath. Brass or nylon brush? Brass (198910) is stronger for stubborn residue; nylon (198920/198930) is gentler. For sensitive coatings, prefer the nylon version. Does the brush replace the ultrasonic bath? No. The brush is for pre-cleaning; thorough cleaning takes place in the ultrasonic bath (UC-50 / UC-60). With the Promed brass brush, you thoroughly free your bits of grinding residue – the ideal first step before the ultrasonic bath.
Promed Sapphire Callus Grinder, Cone (198502) – for calluses and firm areas The Promed callus grinder in a cone shape with a natural sapphire coating removes calluses and hard skin on the feet. The cone shape reaches edges, corners and hard-to-reach areas well – ideal for targeted callus treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Shape: cone – for edges, corners and hard-to-reach areas. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: optimal 10,000, max. 15,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on corners: apply the cone shape precisely to edges and hard-to-reach areas. Hard skin: remove over a wide area in thin layers with little pressure. Tip: never remove too aggressively; work with little pressure and on a regular basis. Technical data Article number198502 Typecallus grinder, cone (sapphire) Materialsapphire (natural corundum) Application areaskin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedoptimal 10,000, max. 15,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with little pressure. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the cone shape good for? The cone shape reaches edges, corners and hard-to-reach callus areas precisely. Can I autoclave the grinder? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the cone-shaped Promed Sapphire Callus Grinder you treat calluses on edges and corners with precision.
Promed Sapphire Callus Grinder, Conical (198501) – for calluses on edges and corners The Promed callus grinder in a conical shape with a natural sapphire coating removes calluses and hard skin on the feet. The conical, tapering shape reaches edges, corners and narrower areas well – ideal for targeted treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Shape: conical – for edges, corners and narrower areas. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: optimal 10,000, max. 15,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on edges: apply the conical shape precisely to corners and narrower areas. Hard skin: remove over a wide area in thin layers with little pressure. Tip: never remove too aggressively; work with little pressure and on a regular basis. Technical data Article number198501 Typecallus grinder, conical (sapphire) Materialsapphire (natural corundum) Application areaskin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedoptimal 10,000, max. 15,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with little pressure. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the conical shape good for? The conical, tapering shape reaches edges, corners and narrower callus areas precisely. Can I autoclave the grinder? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the conical Promed Sapphire Callus Grinder you treat calluses on edges and corners with precision.
Promed Comfort Bit Set (198016) – starter set for nail and foot care The Promed Comfort Bit Set is the convenient starter set for nail and foot care. It bundles a manageable choice of bits for the basic care steps – easy to understand and ideal for a comfortable start. All bits have a shaft Ø 2.332–2.350 mm and fit all Promed nail drills with a 2.35 mm collet. Key features at a glance Focus: starter set for convenient nail and foot care. Contents: a manageable choice of bits for the basic care steps. Application: shortening and shaping nails as well as working on skin and light calluses. Target group: beginners and home users who want to get started easily. Shaft: dental standard Ø 2.332–2.350 mm, suitable for all Promed devices with a standard collet. Cleaning: in an ultrasonic bath; individual bits are autoclavable depending on their marking. What is the set used for and how?The Comfort Bit Set covers the basic care steps: Nails: shorten, shape and smooth on hands and feet. Skin: carefully work on light calluses and firm edges. Tip: work at a low to medium speed and with light pressure – comfortable and easy to control. Technical data Article number198016 TypeComfort Bit Set (starter) Application areaNail and foot care (beginners) ShaftØ 2.332–2.350 mm (dental standard) SterilisationUltrasonic cleaning; individual bits autoclavable depending on marking Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesThe bits fit all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Autoclave only bits marked accordingly – observe the marking of the respective bit. Work with light pressure; in case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) Which devices does the set fit? All Promed nail drills with a standard collet (shaft Ø 2.35 mm). Are the bits autoclavable? It depends on the bit. Please observe the marking of the individual bit; in general we recommend cleaning in an ultrasonic bath. Is the set suitable for beginners? Yes. The Comfort Bit Set is intended as a convenient starter set for basic nail and foot care. With the Promed Comfort Bit Set, you get started with your own nail and foot care in comfort.
Promed Diamond Grinding Cone (198020) – for nail edges and cuticles The Promed Diamond Grinding Cone is a diamond-coated grinding bit for precise, gentle work on the natural nail. The cone shape reaches nail edges, corners and hard-to-access areas well and is ideal for shortening, shaping and working on the cuticle. Diamond works finely and in a controlled manner. Fits all Promed nail drills with a 2.35 mm collet. Features at a glance Material: diamond (diamond-coated) – precise and durable. Shape: cone – ideal for nail edges, corners and pinpoint work. Application: natural nail and skin/cuticle. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Nail edges: shape firm or thickened edges precisely with the cone tip. Cuticle: work on the cuticle gently and in a controlled manner. Tip: work at low to medium speed with little pressure; reduce the speed if heat builds up. Technical data Article number198020 Typegrinding cone, diamond Materialdiamond (diamond-coated) Shapecone Area of applicationnatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including the Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with little pressure; never stay too long on one spot on the nail. In case of diabetes or circulatory disorders, seek medical advice beforehand. Frequently asked questions (FAQ) What is the diamond grinding cone suitable for? For precise work on the natural nail – shaping nail edges and working gently on the cuticle. Diamond works finely and in a controlled manner. Can I autoclave the bit? Yes. This diamond grinding cone is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. Which devices does it fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). With the Promed Diamond Grinding Cone you work on nail edges and cuticles precisely and gently.
Promed Diamond Bit with Cooling Channels, ball-shaped (198545) – for skin, callus and nails The Promed Diamond Bit with cooling channels in a ball shape is diamond-coated and designed for pedicure/foot care – for skin, callus and nails. The cooling channels dissipate heat and generate less friction heat when working on skin, callus and nails. The ball-shaped tip reaches into curves and the nail fold well and is suitable for gently pushing back and working on the cuticle. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape: ball-shaped – for curves, the nail fold and the cuticle. Cooling channels: less heat build-up – less friction heat when working on skin, callus and nails. Application: skin, callus and nails (pedicure/foot care). Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Skin & callus: work on curves and transitions – the cooling channels keep heat build-up low. Cuticle: gently push back and work on the cuticle with the ball-shaped tip. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198545 TypeDiamond bit with cooling channels, ball-shaped MaterialDiamond (diamond-coated) Shapeball-shaped – with cooling channels Application areaskin, callus and nails (pedicure/foot care) ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What are the cooling channels for? The cooling channels dissipate heat and generate less friction heat – ideal for working on skin, callus and nails. What is the ball shape good for? The ball-shaped tip reaches into curves and the nail fold well and gently pushes back the cuticle. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the ball-shaped Promed Diamond Bit with cooling channels, you work on curves and the cuticle gently and with less heat.
Promed Diamond Bit with Cooling Channels, conical/thick (198547) – for skin, callus, nails and wide-area work (pedicure) The Promed Diamond Bit with cooling channels in a conical, thick shape is diamond-coated and specially designed for foot care (pedicure). The cooling channels dissipate heat and generate less friction heat when working on skin, callus and nails. The conical, more powerful shape is suitable for wide-area shortening and removal as well as evenly working out larger areas – well suited to calluses and hardened areas. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape: conical, thick – for wide-area work and larger areas. Cooling channels: less friction heat when working on skin, callus and nails. Application: skin, callus and nails (pedicure/foot care). Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Callus & wide-area work: shorten and remove hardened areas and larger areas over a wide surface – the cooling channels keep friction heat low. Nails & skin: guide the conical, thick shape evenly and in a controlled way. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198547 TypeDiamond bit with cooling channels, conical/thick MaterialDiamond (diamond-coated) Shapeconical, thick – with cooling channels Application areaskin, callus and nails (pedicure/foot care) ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What are the cooling channels for? The cooling channels dissipate heat and generate less friction heat when working on skin, callus and nails. What is the conical, thick shape good for? The more powerful conical shape is suitable for wide-area shortening and evenly working out larger areas – for example on calluses and hardened areas. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the conical Promed Diamond Bit with cooling channels, you work on skin, callus and nails evenly and with less friction heat.
Promed Diamond Bit with Cooling Channels, pointed/small (198544) – for skin, callus and nails (pedicure/foot care) The Promed Diamond Bit with cooling channels in a pointed, small shape is diamond-coated and designed for pedicure/foot care on skin, callus and nails. The cooling channels dissipate heat and generate less friction heat while working on skin, callus and nails. The small, pointed shape reaches narrow edges, the nail fold, corners, ingrown nail edges, fine transitions and the cuticle well. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape/size: pointed, small – for narrow edges, the nail fold and fine transitions. Cooling channels: less friction heat while working on skin, callus and nails. Application: skin, callus and nails (pedicure/foot care). Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Skin & callus: work on transitions and rough areas – the cooling channels keep friction heat low. Narrow spots: apply the small, pointed shape precisely on edges, in the nail fold, on corners, ingrown nail edges, fine transitions and the cuticle. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198544 TypeDiamond bit with cooling channels, pointed/small MaterialDiamond (diamond-coated) Shape/sizepointed, small – with cooling channels Application areaskin, callus and nails (pedicure/foot care) ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What are the cooling channels for? The cooling channels dissipate heat and generate less friction heat – comfortable when working on skin, callus and nails. What is the bit suitable for? For pedicure/foot care on skin, callus and nails: the small, pointed shape is suitable for narrow edges, the nail fold, corners, ingrown nail edges, fine transitions and the cuticle. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the pointed Promed Diamond Bit with cooling channels, you work on skin, callus and nails precisely and with less heat.
Promed Diamond Bit with Cooling Channels, thin/rounded (198546) – for skin, callus and nails, fine work (pedicure) The Promed Diamond Bit with cooling channels in a thin, rounded shape is diamond-coated and specially designed for pedicure/foot care. The cooling channels dissipate heat and generate less friction heat – for fatigue-free work on skin, callus and nails. The thin, rounded shape reaches narrow edges, the nail fold and fine transitions well and works particularly gently. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape: thin, rounded – for narrow edges, the nail fold and fine transitions. Cooling channels: less heat build-up – less friction heat when working on skin, callus and nails. Application: Skin, callus and nails (pedicure/foot care). Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Skin, callus & nails: work on fine transitions and narrow areas on skin, callus and nail – the cooling channels keep heat build-up low. Narrow spots: apply the thin, rounded shape precisely on edges and in the nail fold. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198546 TypeDiamond bit with cooling channels, thin/rounded MaterialDiamond (diamond-coated) Shapethin, rounded – with cooling channels Application areaSkin, callus and nails (pedicure/foot care) ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What are the cooling channels for? The cooling channels dissipate heat and generate less friction heat – pleasant when working on skin, callus and nails. What is the thin shape good for? The thin, rounded shape reaches narrow edges, the nail fold and fine transitions in a targeted way – ideal for gentle detail work. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the thin Promed Diamond Bit with cooling channels, you work on skin, callus and nails with particular fineness and less heat.
Promed Diamond Bit, Teardrop (198542) – for the nail fold and cuticle The Promed Diamond Bit in a teardrop shape is a diamond-coated bit for precise, gentle work on the natural nail. The rounded teardrop shape reaches into the nail fold, edges and curves well and is suitable for shaping and gently working on the cuticle. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape: Teardrop – rounded, ideal for the nail fold, curves and edges. Application: Natural nail and skin/cuticle. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Nail fold: apply the rounded teardrop shape precisely in the nail fold and on curves. Cuticle: work on the cuticle gently and in a controlled way. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198542 TypeTeardrop bit, diamond MaterialDiamond (diamond-coated) ShapeTeardrop Application areaNatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the teardrop shape good for? The rounded teardrop shape reaches precisely into the nail fold, curves and edges – ideal for gentle detail work. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the Promed Diamond Teardrop Bit, you work on the nail fold and cuticle precisely and gently.
Promed Diamond Bit, Teardrop, small (198543) – for the fine nail fold and cuticle The small Promed Diamond Bit in a teardrop shape is a diamond-coated bit in a compact size for particularly fine, precise work on the natural nail. The small, rounded teardrop shape reaches into narrow nail folds, tight edges and curves well and is suitable for gently working on the cuticle. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: Diamond (diamond-coated) – precise and long-lasting. Shape/size: Teardrop, small – for narrow nail folds and fine detail work. Application: Natural nail and skin/cuticle. Shank: Dental standard Ø 2.332–2.350 mm, fits all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Narrow nail fold: apply the small, rounded teardrop shape precisely in narrow nail folds and on tight curves. Cuticle: work on the cuticle gently and in a controlled way. Tip: work at low to medium speed with light pressure; reduce the speed if it heats up. Technical data Article number198543 TypeTeardrop bit small, diamond MaterialDiamond (diamond-coated) Shape/sizeTeardrop, small Application areaNatural nail, skin/cuticle ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Work with light pressure; never stay too long on one spot on the nail. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small teardrop shape good for? The small, rounded teardrop shape reaches precisely into narrow nail folds and onto tight curves – ideal for fine detail work. Can I autoclave the bit? Yes. This diamond bit is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the small Promed Diamond Teardrop Bit, you work in the narrow nail fold and on the cuticle with particular fineness.
Promed Diamond HHS Aero, large (198585) – callus grinder for the feet The Promed Diamond HHS Aero in the large version is a diamond-coated callus grinder for the targeted removal of calluses and hard skin on the feet. The large working surface is ideal for quick, area-wide removal of larger callused patches. Diamond works precisely and in a controlled manner. Fits all Promed rotary tools with a 2.35 mm collet. Key features at a glance Material: diamond (diamond-coated) – precise and durable. Shape/size: HHS Aero, large – large working surface for area-wide callus removal. Application: skin/calluses on the feet. Shaft: dental size Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Pronounced calluses: remove larger callused areas over a wide surface and in thin layers. Hard skin: work evenly with the large working surface. Tip: never remove calluses radically; work with little pressure and regularly. Reduce the speed if heat develops. Technical data Article number198585 TypeHHS Aero large, diamond (callus grinder) Materialdiamond (diamond-coated) Shape/sizeHHS Aero, large Application areaskin/calluses ShaftØ 2.332–2.350 mm (dental size) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed rotary tools with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses radically; work with little pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the large version good for? The large working surface is ideal for quick, area-wide removal of larger callused patches on the feet. Can I autoclave the bit? Yes. This diamond callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the large Promed Diamond HHS Aero you remove pronounced calluses on the feet quickly and evenly.
Promed Diamond HHS Aero, small (198586) – callus grinder for edges and corners The Promed Diamond HHS Aero in the small version is a diamond-coated callus grinder for the targeted removal of calluses and hard skin on the feet. The small working surface reaches edges, corners and narrower spots well – ideal for targeted work. Diamond works precisely and in a controlled manner. Fits all Promed rotary tools with a 2.35 mm collet. Key features at a glance Material: diamond (diamond-coated) – precise and durable. Shape/size: HHS Aero, small – for edges, corners and narrower callused spots. Application: skin/calluses on the feet. Shaft: dental size Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Calluses on edges: apply the small working surface precisely to corners and narrower spots. Hard skin: remove pinpoint and in thin layers with little pressure. Tip: never remove calluses radically; work with little pressure and regularly. Reduce the speed if heat develops. Technical data Article number198586 TypeHHS Aero small, diamond (callus grinder) Materialdiamond (diamond-coated) Shape/sizeHHS Aero, small Application areaskin/calluses ShaftØ 2.332–2.350 mm (dental size) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed rotary tools with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses radically; work with little pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) What is the small version good for? The small working surface reaches edges, corners and narrower callused spots on the feet in a targeted way. Can I autoclave the bit? Yes. This diamond callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the small Promed Diamond HHS Aero you work on calluses at edges and corners in a targeted way.
Promed Emotion (Art. 100030) – Manicure and Pedicure DeviceThe Promed Emotion (Art. 100030) is a handy manicure and pedicure device for home use: automatic push-in collet, clockwise/counter-clockwise rotation, variable speed, LED lighting and a 40-piece grinding set. Collet: push-in collet (automatic). Rotation: clockwise and counter-clockwise. Speed: infinitely variable up to 12,000 rpm. Voltage: 100–240 V AC. Your benefits at a glance Complete care set: 40-piece grinding set with sapphire attachments and a cleaning brush for hands, feet and nails LED light on the device: illuminates the treatment area for precise work Tool-free bit change: automatic push-in collet for all bits in the dental standard Overload protection: stops the motor if blocked/overloaded, protecting the device Gentle control: infinitely variable up to 12,000 rpm with clockwise/counter-clockwise rotation via soft-touch button Areas of application Manicure & pedicure: care of natural nails, treatment of ingrown, thick and hardened nails, calluses, hard skin and the edges of corns. Nail care: cosmetic care of finger and artificial nails. Home use: handy care device for hands, feet and nails at home (indoor use only). Bit compatibility: compatible with the entire Promed bit range (sapphire, diamond, tungsten carbide, ceramic, silicone, felt, leather, textile). Using it is this easy Place the device on your work surface and connect the power adapter. Insert the bit/grinding attachment (dental standard ø 2.332–2.350 mm) into the collet. Select the direction of rotation and set the speed. Work with light, even pressure. After use, clean the bit with the cleaning brush. Technical data ModelPromed Emotion Article number100030 ApplicationManicure, pedicure, nail care (home use) ColletPush-in collet (automatic) RotationClockwise and counter-clockwise Speedinfinitely variable up to 12,000 rpm Voltage100–240 V AC Grinding attachmentsDental standard ø 2.332–2.350 mm Warranty24-month manufacturer's warranty Scope of delivery 1× Promed Emotion (incl. cable and power adapter) 1× 40-piece grinding set with cleaning brush 1× detailed operating instructions Care and safety instructions Cleaning: wipe the outside of the device with a damp cloth – no water inside, do not immerse in liquid. Bits: clean with a bit cleaning brush (Art. 198910 brass or 198920 nylon) and treat with instrument disinfectant. Storage: store in a dry place. Observe the speed limit: every bit has a maximum speed – comply with the specifications. FAQWhich bits fit the emotion?All Promed bits with the standard 2.35 mm shank fit: sapphire, diamond, tungsten carbide, ceramic, silicone polishers, felt, leather and textile. The entire Promed bit range.What does the speed mean?infinitely variable up to 12,000 rpm. Higher speeds allow faster work on hard materials (acrylic); low speeds are ideal for natural nails, cuticles and polishing.What warranty does Promed offer?24-month manufacturer's warranty from the date of purchase. Why Promed?For over 40 years, Promed has stood for high-quality products for manicure and pedicure as well as medical and wellness applications. Tested and certified – used worldwide. Order the Promed Emotion (Art. 100030) now and care for your hands, feet and nails safely and comfortably at home.
Promed Book “Filing Made Easy” (952010) – handbook for professional nail design The Promed handbook “Filing Made Easy” conveys the basic knowledge for professional nail design and the correct way to work with bits and grinding tools. It accompanies the Promed range of bits and grinding tools and is a practical reference work for beginners and professionals in the nail studio. At a glance Topic: professional nail design, handling of drill attachments. For whom: nail studio, foot care and ambitious users. Goes with: Promed bits & grinding tools as well as drill/nail care devices. Content & benefitThe handbook explains step by step how to select and use the right attachments so that you work cleanly, safely and efficiently. This helps you quickly find the right grinding tool for the respective task. Technical data Article number952010 TypeSpecialist book / handbook Title“Filing Made Easy” Topicprofessional nail design Frequently asked questions (FAQ) Who is the book suitable for? For nail studios, foot care and anyone who wants to learn or deepen their knowledge of working with bits and grinding tools. Does the book match my Promed accessories? Yes, it accompanies the Promed range of bits and grinding tools. With “Filing Made Easy”, you get more out of your Promed bits and grinding tools.
Promed Sapphire Callus Grinder Fine (190066) – for smoothing fine finishing The Promed callus grinder in a fine grit with a natural sapphire coating smooths the skin after callus removal and ensures a well-cared-for, soft result. The fine grit is ideal for the final fine finishing. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: fine – for smoothing fine finishing. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: autoclavable (121–134 °C) or in an ultrasonic bath. What is it used for and how? Fine finishing: smooth and refine the skin after coarser removal. Well-cared-for finish: for soft, even skin on the feet. Tip: work with light pressure and even movement; pause briefly if it gets warm. Technical data Article number190066 TypeCallus grinder, fine (sapphire) MaterialSapphire (natural corundum) Gritfine Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationautoclavable (121–134 °C) or ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions After use, autoclave (121–134 °C) or clean in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use fine, when coarse? The fine grit is for the final fine finishing and smoothing of the skin; use a coarser grit for the intensive first removal. Can I autoclave the bit? Yes. This callus grinder is autoclavable (121–134 °C); alternatively, clean it in an ultrasonic bath. With the fine Promed sapphire callus grinder, you can smooth the skin for a well-cared-for finish.
Promed Sapphire Callus Grinder Coarse (190063) – for pronounced calluses The Promed callus grinder in a coarse grit with a natural sapphire coating removes pronounced calluses and hard skin on the feet quickly and over a wide area. The coarse grit is ideal for the first, more intensive treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: coarse – for intensive callus removal. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: in an ultrasonic bath. What is it used for and how? Pronounced calluses: remove over a wide area in thin layers – for the first, coarser working step. Fine finishing afterwards: then smooth with a finer grit. Tip: never remove too much at once; work with light pressure and on a regular basis. Technical data Article number190063 TypeCallus grinder, coarse (sapphire) MaterialSapphire (natural corundum) Gritcoarse Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean after use in an ultrasonic bath (e.g. Promed UC-50 / UC-60). Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use coarse, when fine? The coarse grit is for the intensive first removal of pronounced calluses; use a finer grit for the subsequent fine finishing. Which devices does it fit? All Promed nail drills with a standard collet (shank Ø 2.35 mm). With the coarse Promed sapphire callus grinder, you can remove pronounced calluses quickly and safely.
Promed Sapphire Callus Grinder Coarse (190067) – for pronounced calluses The Promed callus grinder in a coarse grit with a natural sapphire coating removes pronounced calluses and hard skin on the feet quickly and over a wide area. The coarse grit is ideal for the first, more intensive treatment. Fits all Promed nail drills with a 2.35 mm collet. Key features at a glance Material: sapphire (natural corundum). Grit: coarse – for intensive callus removal. Application: skin/calluses on the feet. Shank: dental standard Ø 2.332–2.350 mm, for all Promed devices with a standard collet. Recommended speed: up to 20,000 rpm. Cleaning: in an ultrasonic bath; not autoclavable. What is it used for and how? Pronounced calluses: remove over a wide area in thin layers – for the first, coarser working step. Fine finishing afterwards: then smooth with a finer grit. Tip: never remove too much at once; work with light pressure and on a regular basis. Technical data Article number190067 TypeCallus grinder, coarse (sapphire) MaterialSapphire (natural corundum) Gritcoarse Application areaSkin/calluses ShankØ 2.332–2.350 mm (dental standard) Recommended speedup to 20,000 rpm Sterilisationnot autoclavable; ultrasonic cleaning Compatibilityall Promed devices with a 2.35 mm collet Compatible devicesFits all Promed nail drills with a standard collet (2.35 mm), including Promed 1030, 2020, 3030-X, 4030-SX2, 4040, 5040-SX2, 525/625/725/825, Ultra Pro S as well as Emotion and sensitive. Care and safety instructions Clean after use in an ultrasonic bath (e.g. Promed UC-50 / UC-60); do not autoclave. Never remove calluses too aggressively; work with light pressure. If you have diabetes or circulatory problems, consult a doctor before use. Frequently asked questions (FAQ) When to use coarse, when fine? The coarse grit is for the intensive first removal of pronounced calluses; use a finer grit for the subsequent fine finishing. Can I autoclave the bit? No. This callus grinder is not autoclavable – clean it in an ultrasonic bath. With the coarse Promed sapphire callus grinder, you can remove pronounced calluses quickly and safely.